鋁藝護欄有多種安裝方法。消費者可以根據自己的使用要求選擇合適的安裝方式。安裝時注意調整護欄高度，日常維護，避免生銹。接下來，我們將跟隨廠家了解下護欄的安裝和維護方法。
There are many installation methods for aluminum guardrails. Consumers can choose the appropriate installation method according to their own use requirements. During installation, pay attention to adjusting the height of guardrail and daily maintenance to avoid rust. Next, we will follow the manufacturer to understand the installation and maintenance methods of the lower guardrail.
鋁藝護欄的常規安裝方法：
Conventional installation method of aluminum guardrail:
1、法蘭固定指膨脹螺栓固定。此方法所需的工具包括沖擊錘、膨脹螺栓、錘子、扳手、螺絲刀、卷尺等。擰緊膨脹螺栓時，應注意水泥地面的平整度，并調整立柱的垂直度。
1. Flange fixing refers to expansion bolt fixing. The tools required for this method include impact hammer, expansion bolt, hammer, wrench, screwdriver, tape measure, etc. When tightening the expansion bolt, pay attention to the flatness of the cement floor and adjust the verticality of the column.
2、埋長腿是指挖洞、灌柱。該方法所需的工具包括水泥、砂和礫石等攪拌工具，以及手推車等運輸工具。應注意的是，在澆筑混凝土時，可在澆筑混凝土前用石頭或磚固定柱。起初，只有混凝土才能輕易移動。
2. Burying long legs refers to digging holes and pouring columns. The tools required for this method include mixing tools such as cement, sand and gravel, and transportation tools such as trolleys. It should be noted that when pouring concrete, the column can be fixed with stone or brick before pouring concrete. At first, only concrete could move easily.
3、下預埋鋁件焊接固定。該方法要求預安裝下部預埋鋁。安裝時，立柱或水平管應直接焊接在預埋焊膏上。這要求預埋鋁的尺寸與護欄的尺寸和高度一致。這種安裝速度相對較快。但這種安裝方式會對油漆表面造成一定程度的損壞，損壞的油漆表面應在涂漆前進行打磨。
3. The lower embedded aluminum parts are welded and fixed. This method requires pre installation of lower embedded aluminum. During installation, the column or horizontal pipe shall be directly welded on the embedded solder paste. This requires the size of embedded aluminum to be consistent with the size and height of guardrail. This installation speed is relatively fast. However, this installation method will cause a certain degree of damage to the paint surface, and the damaged paint surface shall be polished before painting.
鋁藝護欄的維護方法：
Maintenance method of aluminum guardrail:
定期除塵：室外灰塵飛揚，隨著時間的推移，一層浮塵會落在鋁制品上。它會影響鋁藝術品的顏色，導致鋁藝術品保護膜的損壞。因此，室外鋁質設施應定期擦拭，通常使用柔軟的棉布。
Regular dust removal: outdoor dust is flying. With the passage of time, a layer of floating dust will fall on aluminum products. It will affect the color of aluminum artwork and cause damage to the protective film of aluminum artwork. Therefore, outdoor aluminum facilities should be wiped regularly, usually with soft cotton cloth.
如果鋁藝護欄因缺乏維護或發生事故而局部生銹，首先用蘸有少量防銹油或縫紉油的棉布定期擦拭鋁護欄表面。如果在鋁護欄上發現銹斑，應將棉紗浸泡在機油中，并盡快涂覆在銹斑上，以去除銹斑，而不是直接用砂紙或其他粗糙表面材料拋光。
If the aluminum guardrail is partially rusted due to lack of maintenance or accidents, first wipe the surface of the aluminum guardrail regularly with a cotton cloth dipped in a small amount of antirust oil or sewing oil. If rust spots are found on the aluminum guardrail, the cotton yarn shall be soaked in the oil and coated on the rust spots as soon as possible to remove the rust spots, rather than polishing directly with sandpaper or other rough surface materials.
運輸和裝卸：包裝應在出廠前完成，以防止裝卸和運輸過程中護欄磨損。如果護欄在安裝過程中再次磨損，油漆會影響護欄的美觀。
Transportation and loading and unloading: the packaging shall be completed before leaving the factory to prevent the guardrail from wearing during loading, unloading and transportation. If the guardrail is worn again during installation, the paint will affect the beauty of the guardrail.
鋁藝護欄由廠家生產后，要經過裝卸、運輸至施工現場的過程，方可安裝。用戶可根據實際情況選擇合適的安裝方式，做好除塵維護工作。
After the aluminum guardrail is produced by the manufacturer, it can only be installed after loading, unloading and transportation to the construction site. Users can choose the appropriate installation mode according to the actual situation and do a good job in dust removal and maintenance.
以上就是為大家介紹的有關山東鑄鐵護欄的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.djse94se.com
The above is a detailed introduction about Shandong cast iron guardrail. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://www.djse94se.com
